WELDED STEEL FRAME, EXTREMLY STABLE AND DURABLE

We start with steel tubing which is cut using lasers for 100% accuracy. Then, the parts are welded into a massive steel frame which is powder coated for a superior protected finish.

Possible dimensions:  300/160 cm
                                    300/210 cm
                                    400/160 cm
                                    400/210 cm
                                    500/160 cm

REDESIGNED LINEAR GUIDE

double bearings increase machine durability and prolong life...

END POSITION HYDRAULIC SHOCK ABSORBERS

They optimize machine performance in a reliable and effective manner by decelerating the roller at the table ends quickly and without recoil.

DESIGNED WITH THE MOTOR RIGHT FROM THE START

Don't work hard, Work Smart...

Motorized drive system, double foot switch and 5 up/down buttons for moving the roller, allow you to completely change the way you use a flatbed applicator. Using traditional tables, the operator works from the area in the middle of the table. With Lamidesk, we have designed everything to happen at the edge of the table . This work area is easily accessible for the operator and allows for mounting that is so quick and easy compared with manual models.

HEATED ROLLER

ESPECIALLY FOR FOTOGRAPHERS OR FOR PRODUCER OF GLASS-PRODUCTS, THE HEATED ROLLER IS A RECOMMENDED FEATURE.

Low shop temperatures can contribute to the occurrence of silvering. 
Using a little heat can help. Adjusting the heat on the top roller, 
can help the adhesive on the overlaminate flow out better.

The heated roller has been standard in Roll Laminators for many years, This provides the advantage of avoiding the "silvering effect". Silvering effect means, that you have encapsulated air, so the glue is not connected to the print on tiny parts of your print material. When working with selfadhesive films, the heat will warm up the glue, so it will fill up the "rough" surface of paper or vinyl. The effect is, that you will have less air encapsulated and the result is more brilliant.
If you are mounting prints behind glass or plexiglass you would need to have a heated roller because the glue should be absolutely transparent. The heated roller would provide a perfect result.
Especially for Fotographers or for producer of glass-products, the heated roller is a recommended feature.

SAVES 60 PERCENT OF THE TIME

COMPARED TO "ORIGINAL" SIGNMAKING FLATBED APPLICATORS, EACH SHEET, AGAIN AND AGAIN

4 REASONS TO NOT CHOOSE "ORIGINAL" MOUNTER
- "original" is not smart
- Lamidesk saves 60 percent of the time compared to 
    "original" signmaking flatbed applicator
- Economic: you can buy much more for some money
- saves healts and energy of your workers, use motor!

MORE EFFICIENT POWER SUPPLY REDESIGNED LINEAR GUIDE

double bearings increase machine durability and prolong life... Built-in active PFC and fan speed control Full corrosion resistant aluminium chassis Conforms to harmonic current IEC/EN 61000-3-2, Class A and Class D Cold start -20°C at 100% load Nominal Input Voltage 85-264Vac, 47-63Hz Mean time between failures: > 700,000 hrs. as per Telcordia SR-332 I/P: 100Vac, O/P: 100% load, Ta: 35°C

MORE THAN 680W LED POWER

OVER 8400 LED CHIPS

The machine comes with a table illuminated by LED strips, giving it an even light coverage of the whole working table. Not only do LED´s minimize power consumption, but they offer proven long life.

COMPRESSOR

You can choose from tree diferent solution: Integrated Supersilent 40 dB, Integrated LC29 72 dB or Stand-alone LC30 supersilent 40dB

5 year parts guarantee

• Spotreba stlačeného vzduchu:  6 bar - 4 l/min.
• Napájanie: 1 x 240V
• Príkon: manuálne modely bez LED osvetlenia a ohrevu valca: 100W
• Štandardná maximálna hrúbka laminovaného materiálu 70 mm – voliteľne až 300 mm